Information For Authors

Authors need to register with the journal web site prior to submitting, or if already registered, you can simply log in and begin the 5 step process. Before submitting you should check the manuscript preparation guideline provided below, and you should also review the copyright notice.

Preparation
All manuscripts submitted will undergo a thorough refereeing process prior to acceptance. Authors may be requested to revise their paper, and the Editor reserves the right to refuse a paper for publication. All manuscript should be written in clear and concise English, and should normally be approximately 8000 words in length.
Manuscripts should be prepared in a common software format to help the type setting when accepted. PDF is the preferred format for initial submission of manuscript on this online system. IJEIS do NOT require extensive formatting work to be carried out by authors, all accepted papers will be professionally type set by the publisher for final publications. The following information is only provided as a general guideline for preparation of your submission.
Paper Structure
Follow this order for structuring of the manuscripts:
  1. Title, Authors, Affiliations, Email
  2. Abstract - A self-contained abstract of approximately 100 – 150 words, outlining in a single paragraph the aims, scope and conclusions of the paper.
  3. Keywords - A list of 3 - 8 keywords, avoid using words such as 'and', 'of', etc. Be sparing with abbreviations, only abbreviations firmly established in the field may be eligible.
  4. Main Text - Suitably divided under decimally numbered headings. Any illustrations and tables should be included in the main text where appropriate with captions.
  5. Acknowledgements - Collate acknowledgements should be in a separate section at the end of the article and do not include them on the title page, as a footnote to the title or otherwise.
  6. References – Please see the Reference section below.
  7. Appendix
Subdivide your paper in the simplest way possible, consistent with clarity, each section should be suitably divided under decimally numbered headings. The text should usually follow the standard sequence of introduction, method, results and discussion. Headings and subheadings for different sections of the paper should be clearly indicated. Ensure that all figures and tables are mentioned in the text and that all references are cited in number order. This online system allows the upload of optional supplement files if it is required.
Tables and Figures
Tables and Figures should be numbered consecutively throughout the paper, referring to them in the text as Table 1, Figure 3, etc. Results should not be presented in both tabular and graphical forms. The minimum of descriptive text should be used on figures with essential information relegated to the figure caption. Graph axes should have the variables labelled in full, with the abbreviation in parentheses. Scale grids should not be used in graphs unless necessary for actual measurements. Author's originals will be used for final typesetting, so the quality of the author's figures will be reflected in the quality of the typeset paper. Authors should therefore provide as good quality figures as possible.
Reference
All publications cited in the text should be presented in a list of references following the text of the manuscript. References should be complete as far as possible, including the year of publication, the publisher and their location, full article, book and conference titles, full list of authors and their initials, and page numbers where appropriate. Indicate references by number(s) in square brackets (e.g. [1, 4, 6]) in line with the text. The actual authors can be referred to, but the reference number(s) must always be given. Present used references numbered in the references section in the order in which they appear in the text. Note that for publication with more than 4 authors; the first 4 should be listed followed by 'et al.'
Examples reference format for conference, journal, book, and book chapter:
  1. Nassis, V, R.Rajugan, Dillon, TS and Rahayu, JW (2005). A Requirement Engineering Approach for Designing Xml-View Driven, Xml Document Warehouses . 29th Annual International Computer Software and Applications Conference (COMPSAC '05), Edinburgh, Scotland, IEEE Computer Society.
  2. Garzotto, F, Paolini, P and Schwabe, D (1993). HDM - a Model-Based Approach to Hypertext Application Design. ACM Transactions on Information Systems (TOIS), 11(1) 1-26.
  3. Mellor, SJ and Balcer, MJ (2002). Executable Uml: A Foundation for Model-Driven Architecture. Boston ; San Francisco ; New York, Addison-Wesley.
  4. Wouters, C, Dillon, TS, Rahayu, JW, Chang, E, et al. (2004). A Practical Approach to the Derivation of a Materialized Ontology View. Web Information Systems. Taniar, D and Rahayu, W. USA, Idea Group Publishing.
Text Layout
The submission file should be in PDF format (this is the preferred format for the initial online submission), or otherwise MS Word, or RTF format.
  • Page – A4 size, number all pages consecutively.
  • Font – 11 or 10 pt font size and standard fonts (e.g Times New Roman).
  • Spacing – Single, or 1.5.
  • Margin – 2.4 cm top/bottom, 3 cm left/right.
Proofs
Correspondence and proofs for checking will be sent to the first named author or the nominated principal contact; this can be selected during the online submission process. Proofs are sent via email in PDF format, and corrections should be returned within two weeks to the publisher. Only type setting changes can be accepted from authors at proof checking stage. Should comment for proofs not be returned within two weeks, it will be assumed that there are no corrections.
Offprint and Reprints
Offprint can be ordered from CRL Publishing (minimum order 100). Offprint must be ordered when returning corrected paper proofs. Details are sent to authors with their proofs for correction, along with a Copyright Transfer form that also need to be return before publication.



:: Site maintained by DEBII - Digital Ecosystems and Business Intelligence Institute, Australia.